So if you were to load V14 onto an original HW-150PVR, it'll detect the old chip and work OK, but won't act any different than with V13. V14 supports the new HW-150PVR with the new chip and remoteįeature-wise, they're all the same and there are QAM versions of each (except V3). V8 (no logo) and V13 (with logo) support the original HW-150PVR with the new remote V3 (buggy) and V10 (bugs fixed) support the original HW-150PVR with the old remote I'd try to make a venture to do this, but I'm not interested enough to devote the time (i.e., if I really cared so much for a better system, I'd just spend 10x and get a Tivo or perhaps the new ChannelMaster at 5-6x if it actually works unlike their most recent attempt.) Someone would release a device based on this mstar soc that's prettier, rear mounted usb port, better ir receiver or better yet RF, and, most importantly, open source firmware that enough people would be keen to develop on so we're not reliant on crap software written by crap developers (homeworx being, seemingly, only one of the less crappy firmwares for these devices compared at least to the iview.) I've ultimately just decided to use the 320gb drive - 40-50 hours of space is sufficient for me and has none of the headaches of troubleshooting the new drive I bought > partitioning the drive only makes a new problem I suspect -> would the homeworx automatically know where to record on the partitions? I'd hate to buy a TiVo and find myself in the same boat again.I suspect it has to do with the peculiarities of the drive/power consumption than anything else (perhaps if I bought a good powered hub that might help) tivo file to ensure their output is going to be compatible though. What attracted me about the TiVo was the ability to record OTA and then copy the recordings to my PC over the network. Recording off air I can just copy the file off the hard drive, run it through a profile I created in VideoReDo and it burns to Blu-Ray perfectly. If I capture a recording from DirecTV I have to do it in real time, THEN let it re-encode it again on the computer (8+ hours) for Blu-Ray. I have DirecTV with an HD-PVR that can record from it via component but the problem is their format isn't to spec for Blu-Ray. I loved their guide setup and it correctly identified all local channels from both my markets. You could forget the marginal channels all together. Even strong channels that I pick up at nearly 100% didn't come in on it, but neither did the slightly weaker channels. It just seems like the slightest variation in signal throws its' tuner all off and it doesn't work at all. I tried everything, I've seen others with the DVR+ post the same information. I wouldn't recommend trying it, sounds like you are in the same situation I am. This time it did the crazy thing where it deletes and rebuilds all my subchannels, and my timer somehow ended up pointing to a completely unrelated channel on a different RF frequency (RF 21 instead of RF 31), which it recorded for about eight seconds! That station records OK on my PC but is just hopeless with the HW. My HW choked on Retro TV again this weekend, but for a different reason than last time. I too have a mix of strong & weak stations (in my case, full-power & low-power stations in the same tower farm), which has been somewhat challenging for my HW-150, but a ton of trial and error aiming my antenna has managed to get the HW working with all but three very weak and useless stations (well, and one station - Retro TV - with unrelated issues). Surprising that the DVR+ is the only device you've had an issue with in your environment. Heed Aleron's warning about the Roamio OTA though: lifetime is expensive up-front but raises the resale value if you ever decide to part with your TiVo, and the OTA doesn't give you that option. Interesting - if all those other devices work OK, then I guess the odds are pretty good that a TiVo (even with only one RF input) will also work.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |